How to replace a water filter on a Manitowoc Ice Machine

How to Replace a Manitowoc Ice Machine Water Filter: Step-by-Step Guide?

Clean water plays an important role in maintaining the quality and consistency of ice produced by commercial ice machines. Whether you operate a restaurant, hotel, café or commercial kitchen, the condition of your ice machine’s filtration system can directly affect water quality and equipment performance.

Over time, water filters collect sediment, while their filtration media gradually reach their service limits. Depending on the cartridge, filtration can help reduce chlorine, unwanted tastes and odours, and mineral scale formation.

Regular Manitowoc ice machine water filter replacement is therefore an important maintenance task.

However, not every Manitowoc water filter uses the same replacement procedure. The correct steps depend on the installed filtration system and cartridge model.

This guide explains when to replace your water filter, how to identify the right cartridge and how to perform the replacement correctly.

For any doubt & Query write us at: sales3@natronequipments.com 

Why Is Water Filtration Important for Manitowoc Ice Machines?

Commercial ice machines require a consistent supply of suitable water to produce ice efficiently.

Water may contain sediment, chlorine and dissolved minerals that can affect ice quality and equipment operation.

A compatible water filtration system helps address specific water-quality concerns.

Helps Improve Ice Taste and Odour

Certain filter cartridges contain activated carbon designed to reduce chlorine and substances associated with unpleasant tastes or odours.

This is particularly valuable for restaurants, hotels and beverage-serving businesses where ice quality influences the customer experience.

Helps Reduce Sediment

Sediment such as sand, dirt and suspended particles can enter the water supply.

An appropriate filtration cartridge captures particles within its rated filtration capability, helping maintain cleaner incoming water.

Helps Control Mineral Scale

Hard water can contribute to scale deposits on ice machine components.

Some Manitowoc-compatible cartridges include scale-inhibiting media designed to help reduce mineral buildup.

However, scale inhibition should not be confused with complete water softening.

Supports Preventive Maintenance

Timely filter replacement helps maintain the filtration system’s intended performance.

It also creates an opportunity to inspect connections, seals and nearby water lines for leakage or visible damage.

When Should You Replace a Manitowoc Water Filter?

The correct replacement interval depends on the cartridge, water conditions and equipment usage.

For specified Manitowoc ArcticPure Plus systems, Manitowoc recommends cartridge replacement every six months or when water pressure through the filtration system drops below 20 psi, whichever occurs first.

Other filtration systems may have different requirements.

Some common warning signs include:

  • Reduced water flow: A clogged cartridge can restrict incoming water.
  • Changes in ice taste or odour: Filter media may no longer be performing as expected.
  • Visible scale deposits: Water treatment may not be adequately controlling mineral buildup.
  • Filter maintenance reminders: Certain equipment configurations may indicate that servicing is required.

These signs can also have causes unrelated to the filter. If symptoms continue after replacement, further inspection may be necessary.

How to Replace a Manitowoc Ice Machine Water Filter?

The following steps describe the general replacement process, with specific details for compatible external ArcticPure Plus filtration systems.

Always follow the instructions supplied with your actual cartridge and filter head.

Step 1: Identify the Correct Replacement Cartridge

Before purchasing a replacement, record the ice machine’s model and serial number.

Next, inspect the installed water filtration system and locate its model information.

Check the existing cartridge for a manufacturer reference or part number.

This matters because Manitowoc equipment may use external ArcticPure or ArcticPure Plus systems, as well as other model-specific filtration arrangements.

Cartridges that appear similar may have different dimensions, connections or filtration specifications.

Choosing the correct replacement helps ensure compatibility with the installed filter head and equipment.

Step 2: Prepare the Ice Machine and Work Area

Once you have identified the correct cartridge, prepare the work area.

Keep a clean cloth and suitable container nearby to collect any residual water.

Follow the manufacturer’s instructions for placing the ice machine into the appropriate maintenance or shutdown condition.

Before removing the cartridge, determine whether the filter head automatically isolates the water supply.

Certain external ArcticPure Plus systems feature internal shut-off valves that operate when the cartridge is released.

Other filtration systems may require the water supply to be isolated manually.

Follow the procedure for your specific system.

Step 3: Remove the Existing Water Filter

For the external ArcticPure Plus systems covered by Manitowoc’s replacement instructions, cartridge removal involves a quarter-turn mechanism.

Turn the existing cartridge approximately one-quarter turn to the left until it stops.

This movement closes the applicable water ports and allows pressure to be relieved through the designed mechanism.

Gently pull the cartridge downward to remove it from the filter head.

Keep a container underneath to collect residual water.

Avoid forcing a cartridge that does not release normally. Refer to the manufacturer instructions if additional resistance is encountered.

Dispose of the used cartridge according to applicable disposal requirements.

Step 4: Inspect and Install the New Cartridge

Before installation, inspect the replacement water filter for visible damage.

Check its casing, connection points and O-rings where applicable.

For the specified ArcticPure Plus system, Manitowoc requires suitable food-grade lubricant for the O-rings and warns against using petroleum jelly.

Remove the protective cap from the replacement cartridge according to the instructions.

Push the cartridge into the filter head and turn it approximately one-quarter turn to the right until it reaches the fully engaged position.

For the applicable ArcticPure Plus connection, the top of the cartridge should sit flush against the bottom of the filter head.

Ensure the cartridge is correctly seated before proceeding.

Step 5: Flush the New Water Filter

Flushing is an important stage after cartridge replacement.

New carbon-based water filters may release small amounts of carbon fines during initial operation. Air may also be present inside the filtration system.

The flushing process helps clear these materials before normal equipment operation.

However, flushing times differ between Manitowoc filter systems.

For certain external ArcticPure Plus cartridges, Manitowoc specifies a 10-minute flush through the downstream flush valve, where installed.

Other Manitowoc filtration cartridges may require different flushing periods or machine-specific procedures.

For this reason, never assume that one flushing duration applies to every Manitowoc water filter.

Follow the instructions supplied with your exact cartridge and ice machine.

Step 6: Inspect for Leaks and Restore Operation

After installation and flushing, inspect the filter head and surrounding water connections.

Check for dripping, loose connections or visible moisture.

If leakage is detected, stop and follow the applicable troubleshooting instructions.

Once the installation is confirmed, restore the ice machine to normal operation according to the equipment manual.

Check that the machine receives water correctly.

If the equipment includes a filter replacement reminder, reset it using the model-specific procedure.

Record the replacement date and cartridge reference for future maintenance.

Common Mistakes to Avoid

A few common mistakes can make water filter replacement less effective.

Using the wrong cartridge: Always match the filter model and manufacturer reference rather than choosing by appearance.

Skipping flushing: Follow the specified flushing procedure to clear trapped air and loose carbon fines.

Ignoring damaged seals: Damaged O-rings or incorrect installation can cause leaks.

Missing the replacement schedule: Keep maintenance records so that cartridges are replaced at the correct intervals.

Source Manitowoc Ice Machine Spare Parts From NESPL

At Natron Equipment & Spares Pvt. Ltd. (NESPL), we supply Manitowoc ice machine spare parts to customers across India, helping businesses source replacement components for their commercial ice-making equipment.

Our product range includes various Manitowoc-related components, such as water inlet valves, control boards, water level probes, pumps and other specialised spare parts.

If you are looking for replacement water filters or other components for your Manitowoc ice machine, we can help you explore suitable sourcing options. To identify compatible products, please share your ice machine model, filter system details and existing cartridge reference. This information helps us check product compatibility and availability.

We serve commercial kitchens, restaurants, hotels, equipment maintenance teams and procurement professionals looking for dependable spare-parts sourcing solutions in India.

For product specifications, availability and quotations, contact us at sales3@natronequipments.com. Our team will be happy to assist you with your requirements.

Must Visit to buy: https://www.natronequipments.com/

Conclusion

Regular Manitowoc ice machine water filter replacement helps maintain suitable water quality and supports consistent commercial ice production.

Identifying the correct cartridge, following the specified replacement procedure and completing the required flushing steps are essential for effective maintenance.

Businesses should also maintain replacement records and inspect the filtration system regularly to identify potential problems early.

We, at NESPL, help businesses across India source Manitowoc ice machine spare parts and compatible replacement components, with support for product enquiries, availability checks and quotations.

Frequently Asked Questions

1. How often should I replace a Manitowoc ice machine water filter?

For specified ArcticPure Plus systems, replacement is recommended every six months or when water pressure through the filtration system drops below 20 psi, whichever occurs first. Check the instructions for your particular cartridge.

2. Can I replace a Manitowoc water filter myself?

Certain quick-change cartridges can be replaced using the manufacturer’s procedure. However, if the installation is difficult to access, leaking or requires specialised servicing, contact a qualified technician.

3. How long should I flush a new Manitowoc water filter?

Flushing duration depends on the cartridge. Certain ArcticPure Plus systems specify 10 minutes, while other Manitowoc cartridges have different requirements. Always follow the relevant instructions.

4. How do I identify the correct replacement water filter?

Check the ice machine model, filtration system model and existing cartridge part number. Use these details to confirm compatibility before purchasing a replacement.

RELATED ARTICLES